• Cart: 0 items

Rovac® Chmney Video Inspection System


  • Model: 9671A
  • Quantity:


  • 2.4 GHz Wireless receiving mode Digital Video Recorder/Monitor
  • Fold-away antenna and pop-out  “kickstand” 
  • Records video from the included wireless or wired cameras
  • Allows photo to be taken and recorded using video/photo switch
  • 3200 mAhr Li-battery w/10 hrs record time (1 hr time w/camera lamps on)
  • Built in speaker
  • MicroSD Card slot, 32 GB (Included) Max
  • Auto shut-off and screen saver

Basic Setup - The 5” wireless color monitor is also a digital video recorder.  Charge up using the mini-USB AC or computer cords provided.  6-10 hours initial charge then, when in use, 4-6 hours are needed for a full charge.  Unplug when charge is complete!  A microSD card is in the slot on the left side of the camera if recording is desired.  Screw on the antenna to the right side brass fitting and adjust for use. Always store antenna down and tucked away to prevent damage.  Install the video signal cable as shown in the manual.  Push power button for 3-5 seconds and release to start unit and see the splash screen.

NOTE: The USB Chargers are for this unit only!  If using this device infrequently charge it every 2-3 months for longest life.  You can use the unit while charging but battery does suffer somewhat from partial charging.

Wireless Camera with swivel mount base

The wireless camera has a limited range in chimneys but is good for handheld scanning of smoke chambers, thimbles, or chimney exterior.  Charge ONLY with provided charger for AC or charger for auto.  Front red light will show during charging and turns off at full charge.  Note the wireless camera charger plug tip is very small. The chargers for the monitor are mini-USB.  Charge camera for 2 hours prior to use.  Hold power button down for 3-5 seconds then release to engage camera light.  Hit twice to brighten the lamps if needed. Quickly turning off the light will maintain video signal.  Hold button down to totally kill power thus saving battery.  Run time is 1 1/2 hours max.  Be sure to power down when finished.  To view image turn on wireless DVR and signal will automatically be received so long as the wired camera is notin use. NOTE: Verify you have turned off wireless completely by holding button down over 5 seconds.  Use monitor to verify wireless camera is off!

Wired Camera w/AC Power adapter and switchable LED.

This camera comes equipped with a highly sensitive CMOS sensor, high luminous flux (f/1.2) and wide view angle (90°) in a small size.

10 high brightness white light LED lamps enable the effective recording distance of up to 16’ (5m) in complete darkness.

Camera provides 520 lines of resolution in true color.

The ButtonLok centering device protects and holds the wired camera securely with a view straight up (only) the chimney or duct being inspected.

The AC charger may be used to run system or charge using port shown. There is a touch of paint on the cable end and monitor that will match. The cable end of the camera has a 3.5mm plug and on/off LED switch.  The correct connection is as shown in the manual.  The wired camera 3.5mm end goes into the only port it fits. 




Additional Information

  • Model: 9671A
  • Manufactured by: A.W. Perkins Co.
  • Products Price: $ 899.00 + tax
    Availability: In Stock


Our products come with a 12 month replacement warranty. The warranty covers all non-wearable parts and joints on our Rodtech Click range. It does NOT cover misuse of equipment or when the equipment is used with the tile breakers It does not cover parts that will wear with use, such as head inserts (Co-polymer, Chain and Wire etc) You must read the manual for guidance. In the unlikely event you will ever need to use this warranty, you will be required to return the product to Rodtech or a Rodtech Agent before a replacement part is supplied (subject to being used in accordance with our user manual).